Thirdrail7
Engineer
- Joined
- Jul 9, 2014
- Messages
- 4,542
One of the main things left out (aside from the fact that this isn't Canada and there are different regulations) is the aforementioned blue flag rules. If mechanical is involved, things take time and that is due to federal regulations governing their movement between equipment...particularly if the moves are made on a main track.
Here is an example from the The Engine Switcharoo thread.
Debris has been known to fly up and partially close angle cocks which actually led to the back up hose/ valve or emergency valve test rule. The rule was also amended to test it where the back up move will begin. Otherwise, when you back up, something drives in front of you and when you place the train in emergency....and it doesn't dump, you aren't surprised.
But, I bet you didn't think of that.
If you don't use it, you lose it and that assumes you had it to begin with. Do you remember every single driving regulation?
Here is an example from the The Engine Switcharoo thread.
Scenerio for ground PowerCan't attach and detach the power cables while the train is energized, so the process would be more like.
1. Show up
2. Power down.
3. Detach locomotives.
4. Attach ground power while locomotive drives away.
5. When new locomotive arrives, power down and disconnect ground power.
6. Attach new locomotives.
7. Restore power.
Now you've added time to the evolution and still have two different outages while the work is done. Not worth it.
1.Show up as train arrives,
2.Call K Tower to lock up switches for Blue Flag Protection
3. When confirmed put Blue lights in track front and rear.
4.Put Blue light in engine cab
5..Power Off
6. Detach locomotives cables, turn off air supplies
7.. call K tower and remove blue flag protection.
8. Take blue lights off track
9. Take blue light off engine
10. Turn off overhead lights
11. uncouple locomotive
12. wait for locomotive to clear track and switches
13. Call K Tower to lock up switches for Blue Flag Protection
14. When confirmed place blue light in track in front and rear.
15. Turn on Blue overhead lights
16. Attach Ground power cables at one end of consist
17. Loop 480 cables at other end of consist
18. Turn on Ground Power
19. Call K Tower give up Blue Flag Protection
20. Remove Blue lights from track
21.Turn off overhead lights.
21. Diesel Locomotive arrives
22. Couple up locomotive
23. Call K Tower to lock up switches for Blue Flag Protection
24. Put Blue lights in track front and rear. Put Blue light on engine
25. Turn on Blue overhead lights
26. Turn off Ground power
27. Detach Ground power cables
28. attach cables, brake hoses and main recseviour air to locomotive
29. Do brake test
30. Call K tower and give up Blue Flag Protection,
31. blue take lights out of track
32. turn off overhead blue lights
33. remove bue light from engine cab
33. Train can leave
Putting the train on ground power will likely lengthen the time the train is without power!
Actually, they aren't typically testing the brakes. They are testing the back up hose/valve or the emergency valve to make sure if an emergency occurs, the train can be stopped A.S.A.P. Just because the brakes worked from the engine doesn't necessarily mean that they will work from another valve at the opposite end of the train. That is why it is a federal rule that not only will brake tests be performed when controlling ends change, a running test must be performed.That is very accurate. Now there are some other useless things we have to do to you forgot. Why Amtrak has to do a brake test when they back up before coupling up. Especially when the train already has proven over the course of miles it has functional brakes.So that's 1 thing that takes some time....
Debris has been known to fly up and partially close angle cocks which actually led to the back up hose/ valve or emergency valve test rule. The rule was also amended to test it where the back up move will begin. Otherwise, when you back up, something drives in front of you and when you place the train in emergency....and it doesn't dump, you aren't surprised.
But, I bet you didn't think of that.
Replace "K Tower" with the appropriate dispatcher and you have the basic procedures for mechanical working on a train outside of a r.i.p track, car servicing and/or engine repair track.So more of a Amtrak procedural/policy delay or equipment too old(Amtrak equipment) that it takes too much time? When they coupled and decoupled the LRC cars on ViaRail, I was excepting 30+ minutes because of experience on Amtrak, but after like less than a minute of power outage, we were on our way.
Perhaps you should use the word inexperienced. There are crews that rarely have to switch cars or get in between the equipment. That is because they work in areas without yards or work through movements. Therefore, when they finally comes time to switch cars or there is an emergency, they may have to apply rules and procedures that they may not have used in the field for years. So, they take their time.That's because of how incompetent some switch crews are. I'm not saying all are incompetent but there are quite a few that are.
If you don't use it, you lose it and that assumes you had it to begin with. Do you remember every single driving regulation?